4mm VibroFiltr Sound Deadening Mats

73.00146.00

Not too sure what to order? Get free samples first!

(comes in a pack of 10 sheets)

smaller quantities can be purchased in store

4mm VibroFiltr soundproofing damping mats are composed of butyl rubber and aluminum foil, which eliminates noise and resonance created by car body elements. It uses mass loading to lower panel resonance and absorb structural vibrations, converting them into low level heat.

Where to apply the product:

  • Floor
  • Wheel arches
  • Bulkhead
  • Transmission tunnels
  • Suitable for areas that suffer from bad vibrations the most

Damping mats are self-adhesive. To apply, thoroughly clean the area, cut mat to size and firmly press down the material on the prepared surface (for better results use a roller).

  • Thickness: 4mm
  • Size:
    • Small Sheets: 0.50m x 0.35m (19.68″ x 13.77″)
    • Big Sheets: 0.50m x 0.70m (19.68″ x 27.55″)
  • Cover Area per Sheet: 
    • Small Sheet: 0.175 sq.m (1.88 sq.ft)
    • Big Sheets: 0.35 sq.m (3.76 sq.ft)
Clear
SKU: N/A Category:

Description

DAMPING MATS

ABOUT:

VibroFiltr soundproofing damping mats eliminate noise and resonance created by car body elements. It uses mass loading to lower panel resonance and absorb structural vibrations, converting them into low level heat. VibroFiltr damping mats are flexible, self-adhesive, composed of butyl rubber and aluminum foil. In addition, the professional material helps to insulate your vehicle and reduce outside noise. In the end, all of these key characteristics combine together to dramatically improve the sound of your car interior.

INSTALLATION:

The 4mm thickness damping mats are perfect for areas that suffer from bad noise and vibrations the most. These include wheel arches, boot, floor, bulkhead and transmission tunnels. For best results, the material must be installed on a vehicle’s internal metal panels. Just measure, cut and apply to the mentioned surfaces. In order to maximize the use of VibroFiltr damping properties, the mat must be firmly pressed during assembly (e.g. by means of a roller), so that it adheres perfectly without creating a space with air bubbles.

COMBINING PRODUCTS:

During the entire silencing of the vehicle, three different type of materials can be applied. The products can be layered, where each one has different properties and operates in different frequency ranges.

Highest quality soundproofing can be achieved by combining the following:

1. Aluminum – butyl damping mats:

Firstly, this product is applied to the vehicle’s metal body elements. The mats dampen the vibrations and low frequency noise created by these parts.

2. Foam insulation barriers like rubber or polyethylene foam:

Secondly, foam is placed on top of the damping mats. It helps to block the passage of medium and high frequency road noise inside the vehicle.

3. Soft materials like acoustic foam

Lastly, acoustic foam is added.  It absorbs sound and resonances created by plastic upholstery elements.

All of the materials listed above can be purchased on our website. If you have any questions regarding the combination of products do not hesitate to contact us.

OTHER Specifications:

  • USE: self-adhesive mat for damping vibrations, noise and acoustic resonances
  • SHEET THICKNESS: 4.0 mm +/- 0.2 mm
  • THICKNESS OF ALUMINUM FOIL:  0.1 mm (100 μm)
  • SHEET DIMENSIONS: 0.50m x 0.35m | 0.50m x 0.70m
  • SURFACE AREA PER SHEET: 0.175 sq.m | 0.35 sq.m
  • WEIGHT PER SHEET: 1.21kg (6.94kg/sq.m) | 2.42kg (6.94kg/sq.m)
  • MECHANICAL LOSS COEFFICIENT (MLF): 0.60 – vibration suppression efficiency (more = better)
  • RECOMMENDED INSTALLATION TEMPERATURE: above + 18ºC
  • TEMPERATURE RANGE OF USE AND OPERATION: -50ºC to + 160ºC
  • STRENGTH OF MATERIAL BINDING TO THE SURFACE OF THE METAL: not less than 6N/sq.cm
  • ADHESION: maximum adhesion of the viscous butyl polymer to the substrate achieved in 12 hours after sticking (depending on the temperature)
  • OTHER  PROPERTIES: self-vulcanizing product with anti-corrosion and sealing properties, waterproof, does not contain bitumen additives (without tar and asphalt), non-toxic, non-staining, does not emit unpleasant odors, can be used in the automotive industry and indoors